ROPER Range/Stove Oven BES, BEP models

Failure Code Condition Check/Repair F2 Bake/Clean temperature runaway alarm 1. Allow unit to sit for one hour to cool down 2. Place oven temperature sensor in a glass of ice water 3. Measure oven temperature sensor resistance. The oven temperature sensor should measure about 1000 ohms while in the ice water   · If the oven temperature sensor is good but the problem remains replace the electronic range control (ERC) · If the oven temperature sensor is bad, replace it F3 Oven temperature sensor circuit open Verify the oven temperature sensor wiring harness is OK, if so, replace the oven temperature sensor. F4 Shorted oven temperature sensor circuit Verify the oven temperature sensor wiring harness is OK, if so, replace the oven temperature sensor. F5 Element relay enable on. (STUCK CLOSED) Replace the electronic range control (ERC) F6 Power was interrupted Push the OFF/CANCEL button F8 Improper door lock points 1. Check the door latch switch 2. Check the 8-pin connector on the control for a good connection Replace the electronic range control (ERC) if the connections and latch switch check out OK.

Roper Range/Stove 24" Built-In Self-Clean Wall Oven

Failure Code Condition Check/Repair F2 Oven temperature above specifications 8-pin connector oven temperature sensor to the Electronic Range Control (ERC) F3 Open oven temperature sensor Check wiring harness, replace oven temperature sensor if necessary F4 Shorted oven temperature sensor Check wiring harness, replace oven temperature sensor if necessary F5 Pushbutton stuck Check for binding of pushbuttons and control panel glass. If OK, replace touch panel F6 Computer logic interrupted (timing) Replace Electronic Range Control (ERC) F7 Computer logic interrupted (lock motor) Replace Electronic Range Control (ERC) F8 Computer logic interrupted Replace Electronic Range Control (ERC)

ROPER
Range/Stove/Oven Fault Codes
NOTE: Not valid for Y line. If there is a Y near the end of your model number, do not use this chart.

Failure Code	Condition	Check/Repair
4 Digit Failure Code
F0 - E0	Analog to Digital Failure	Disconnect for 30 seconds - if display re-appears - replace control
F1 - E1	Safety flip flop	Replace Electronic Range Control/Clock (ERC)
F2 - E0	Shorted keypad	Replace Electronic Range Control/Clock (ERC)
F3 - E0	Oven temperature sensor or oven temperature sensor fuse opened	Replace oven temperature sensor or fuse
F3 - E1	Oven temperature sensor shorted	Replace oven temperature sensor
F3 - E2	Oven too hot	Replace oven temperature sensor
F3 - E3	Clean temp too hot	Replace oven temperature sensor
F5 - E0 F5 - E1 and E2	Door latch problem	Check door/latch switch, replace if necessary
2 Digit Failure Code
F0 or F1 or F5	Failed Electronic Range Control (ERC)	Replace Electronic Range Control/Clock (ERC)
F2 - E0	Oven temp too high	1. Test operation of door lock on self-clean models 2. Test relay contact operation 3. High resistance in oven temperature sensor
F3	Open oven temperature sensor or thermal fuse, bad oven temperature sensor harness, or oven temperature sensor resistance too high	Replace oven temperature sensor or thermal fuse
F4	Shorted oven temperature sensor	Replace oven temperature sensor
F6	Problem in time keeping circuit	1. Reset time and/or cooking operation 2. Check for proper ground
F7	Stuck function switch or button on Electronic Range Control (ERC)	Replace Electronic Range Control/Clock (ERC)
F8	Failure of Electronic Range Control (ERC)	Replace Electronic Range Control/Clock (ERC)
F9	Door lock circuit	Check wiring and test operation of door lock switch
DOOR	Bake or Broil · Defective latch switch · Shorted wire from ERC 10-pin connector, pin 10 to ground · Door latched	Replace latch switch if defective.Replace wire from 10-pin connector if defective
DOOR	Self-Clean · Defective latch switch · Open wire from ERC 10-pin connector, pin 10 to ground · Door not latched	Replace latch switch if defective.Replace wire from 10-pin connector if defective
LOCK	Not in Self-Clean · Oven temperature sensor resistance too high	Check oven temperature sensor resistance, wire harness and connections, replace defective component

ROPER
Range/Stove Oven- Alternative 2 Digit Fault Codes

Failure Code	Condition	Check/Repair
F1	Analog to Digital Failure	Disconnect for 30 seconds - if display re-appears - replace control
F1	Safety flip flop	Replace component
F1	Shorted keypad	Replace component
F3	Oven temperature sensor opened	Measure oven temperature sensor resistance, should be1100 ohms. If not, replace sensor
F2	Oven temperature sensor shorted	Replace oven temperature sensor
F3	Oven too hot	Replace oven temperature sensor
F3	Clean temp too hot	Replace oven temperature sensor
F5	Check door/latch switch	Replace component