Press ( CTRL )  and the letter ( F ) on your keyboard to pop up a search box. Then you may put in your code to make your search easier.

F1 codes all below :
F10 Control has sensed a potential runaway oven condition. Control may have shorted relay,RTD sensor probe may have gone bad. ( replace RTD sensor or EOC or both)
F11 Shorted Keypad (replace keypad)
F13 Control's internal checksum may have become corrupted.(unplug unit replug back in)
F14 Misconnected Flat cables. (reconnect cables,if not replace board)
---------------------------------------- ---------------------------------
F3 codes all below:
F30 Open RTD sensor probe or wiring problem. (may also show F1 codes) (replace sensor)
F31 Shorted RTD sensor probe or wiring problem (replace sensor)

--------------------------------------------------------------
F9 codes below:
F90-F94  Door mechanism failure. ( Press clear key ) (check wiring of lock motor,switch, and circuits)
Check for lock motor driving by applying voltage to motor direct. Replace if needed. Replace motor lock assembly.) If all does not correct replace EOC board.

Newer Frigidaire range fault codes ( Some Kenmore ranges are built by Frigidaire EG:417.######## )
Fault Code Likely Failure Condition/Cause Suggested Corrective Action

F10  Runaway Temperature.

F11  Shorted Keypad.

F12  Bad Micro Identification.

F13 Bad EEPROM Identification/Checksum error.

  1. (F10 only) Check *RTD Sensor Probe & replace if necessary. If oven is overheating, disconnect power. If oven continues to overheat when the power is reapplied, replace EOC. Severe overheating may require the entire oven to be replaced should damage be extensive.

2. (F11, 12 & 13) Disconnect power, wait 30 seconds and reapply power.

3. (F11, 12 & 13) If fault returns upon power-up, replace EOC.
 
F30 Open probe connection.

F31 Shorted Probe connection.

 1. (F30 or F31) Check resistance at room temperature & compare to *RTD Sensor resistance chart. If resistance does not match the RTD chart replace RTD Sensor Probe. Check Sensor wiring harness between EOC & Sensor Probe connector.

2. (F30 or F31) Check resistance at room temperature, if less than 500 ohms, replace *RTD Sensor Probe. Check for shorted Sensor Probe harness between EOC & Probe connector.
 
F90 Maximum oven door unlock time exceeded.

F91 Maximum oven door unlock attempts exceeded.

 

F92 Maximum oven door open time exceeded.

 

F93 Maximum oven door lock time exceeded.

F94 Maximum oven door lock time exceeded.

Maximum oven door lock attempts exceeded.
 1. (F90, 91, 92, 93 & 94) Check the wiring between EOC & Lock Motor Micro Switch.

2. (F90, 91, 92, 93 & 94) Replace the Motor Door Latch assembly if necessary.

3. (F90, 91, 92, 93 & 94) Check for binding of the Latch Cam, Lock Motor Rod & Lock Motor Cam.

4. (F90, 91, 92, 93 & 94) Check to see if Lock Motor Coil is open. If open, replace Lock Motor Assembly.

5. (F90, 91, 92, 93 & 94) Lock Motor continuosly runs - if Micro Switch is open, replace Lock Motor Assembly.

6. (F92, 93 & 94) Check oven door Light Switch - if open, replace Switch.

7. If all situations above do not solve problem, replace EOC.

Frigidaire Dishwasher:
UO :Vent open: While in wash cycle ,main control does not receive signal from vent assembly that vent plunger is closed. Plunger
status is sensed with optical sensor in vent assembly. Check wiring between vent assembly and main control board. If wiring correct,replace vent assembly. If error still exist, replace main control board.
UF: Fan not running , While in drying cycle,main control not sensing vent fan motor rotation at correct speed. Check wiring between vent assembly and main control board. If correct,replace vent assembly. If error still exist replace main board.
ER: Membrane switch failure, Main control has detected a stuck key or a key pressed for more than one minute. Check connections. If correct replace key pad. If still exist replace main control.
CE: Configuration error , check wiring at control and key pad. check for correct part number installed.
CL: Close door-door switch error , main control not sensing door closed. close door. check door switches.check wiring between door switches and main control. if ok, replace main control.
dP: Drain pump, displayed in relay test when drain pump is activated.
FL: Water valve is open, displayed in relay test when drain pump is activated.
HO: Heat relay, The control is delaying cycle to allow water temperature to rise to correct temperature in attempt to assure optimum performance
hs: Hall sensor: The control has sensed an error with the hall sensor in motor. Check wiring between motor an main control. If still exist replace motor,then main control.
LO: Low rinse aid, Rinse aid level is low. Refill
PF :Power failure More than 10% POWER HAS DROPPED TO THE DISHWASHER.  Check house wiring.
rA: Rinse aid: The control has sensed a problem with the reed switch in the dispenser. Refill the rinse aid dispenser. If error still exist,
check wiring between dispenser and main control board. If not corrected ,replace dispenser assembly. If still exist ,replace main control.
RE: Rinse aid reed switch: Rinse aid reed switch in dispenser is closed.
RF: Rinse aid, Rinse aid reed switch in dispenser is open. Refill rinse aid dispenser. Replace dispenser assembly.
rt:   Relay / triac test, Relay test mode has been activated
Sd: Detergent dispenser Displayed in relay test mode when detergent dispenser is activated.
tu:  Turbidity Sensor: The main control has sensed a failure in the turbidity sensor.Check wiring. If correct,replace turbidity sensor, If error still exist , replace main control board.
UL: UL test mode, Displayed in relay test mode when UL test is activated.

Frigidaire Tumble action Washer models ( front loads )

F1   ( an internal fault in the control) Replace control if doesn't clear.
F2   ( A water temperature problem ) Check water temperature sensor. Readings should be more than 3K but not more than 163K. Mearsure resistance between pins 3 and 4 from the 4 wire plug off the control board. If the reading is same as the sensor readings replace control.  If not the same replace defective wiring.
F3  ( Water level problem caused by incoming or drain pump is not working. ) Check pressure switch or tubing from pressure switch. Also check drain pump and blockage on drain.
F4  ( The washer is not advancing through it increments )  Possible motor speed control or control board.
F5  ( keypad problem ) Replace touch pad, keypad.
ddo ( Drawer reed switch not closed. ) Reclose drawer , check reed switch and magnet
dr   ( Door switch is not closed ) Replace door lock assembly if door is closed properly.

Frigidaire Dryer Fault codes GLE942CS0 AND GLQ942CS0.

F01   ( internal fault in the control )  Replace control
F02   (Control temperature sensor open or shorted) Check temperature control sensor, and replace control board if sensor good.
F03  ( No heat ) Replace control if all heating circuits check good.
F04   ( The drying time has exceeded the program time for that cycle. ) Dryer not heating, restricted vent, blower fan blade broken or loose, dryer in a closet closed door, bad connection in sensor bar circuit or dirty sensor bars. If all correct replace control.
F5   ( a problem with the key pad ) Replace keypad.
PAU  ( A problem with power to the motor ) Check connections to control board, door switch, thermal limiter, or motor.

Frigidaire ( front load washer )                       

E10 / E11     ( fill time too long. )
E13      ( water leak in tub or air leak in air bell )
E14     (reed switch) Dispenser drawer issue with magnet
E20 / E21 / E22      ( Water not pumping out fast enough ) Drain pump or control issue
E23      ( Drain pump relay on control board failed or wire off pump )
E24      ( Drain pump relay on control board failed or wire off pump )
E31      ( Pressure sensor not communicating with control board )
E32     (Pressure sensor calibration problem)
E35      ( Pressure sensor indicates water overfill )
E36      ( control board problem ,replace control )
E38      (Air trap clogged) Check valve, pressure switch,and main board
E40      ( Door switch or main control board problem )
E41      ( Control board thinks the door switch is open )
E42      ( Door remains locked after cycle is complete) Check main board and door switch
E43      ( Control board problem ) Replace
E44      ( Control board problem ) Replace
E45      ( Control board problem ) Replace
E46      ( Control board problem ) Replace
E47      ( Board thinks the door PTC circuit is open in spin )
E48       ( Board thinks the door PTC circuit is closed )
E49       ( Door incongruence between door line and door sense) Check for obstruction,door switch, main board,door striker
E52       ( Bad signal from tacho generator )
E53       ( Low voltage to speed control board ) Check wiring between main board and speed control board. If good replace speed control.
E54       ( Over speed) Check motor if free, check tub for obstruction, check motor windings if other than between 105-130.If not replace speed control.
E55       ( Motor overheating ) Check motor if free, check tub for obstruction, check motor windings if other than between 105-130.If not replace speed control.
E56       ( High motor current ) Check motor if free, check tub for obstruction, check motor windings if other than between 105-130.If not replace speed control.
E57       ( High current on inverter ) Check motor if free, check tub for obstruction, check motor windings if other than between 105-130.If not replace speed control.
E58       ( High current on motor phase )  Check motor if free, check tub for obstruction, check motor windings if other than between 105-130.If not replace speed control.
E59       ( No tacho signal for 3 seconds )
E5A       ( High temp on heat sink caused by overloading. Replace speed control board)
E5B       ( High temp on heat sink, replace speed control board)
E5C       ( High temp on heat sink, replace speed control board)
E5D       ( Communication problem )
E5E       ( Communication problem )
E5F       ( Communication problem )
E66       ( Heating element relay failure )
E67       ( Input voltage on microprocessor incorrect )
E68       ( Current leakage to ground on heater or fuse opened )
E70       ( The control board is not seeing the correct water supply )
E71       ( Wash NTC failure. (Tub heater) Replace control board or wire. )
E74       ( Wash temperature does not increase. Place NTC in correct position )
E75       ( Water temperature sensor circuit )
E76       ( NTC temperature for the cold water valve over the limits. Hot and cold-water hoses switched )
E82       ( Console control problem . Replace control board )
E83       ( Console control problem. Replace control board )
E91  / E92     ( Communication error between UI board and control board. Check wiring )
E93       ( Console control problem. Replace control board )
E94       ( Console control problem. Replace control board )
E95       ( Communication error. Replace control board )
E97       ( Console control problem. Replace control board )
E98       ( Console control problem. Replace control board )
EA1      ( Power supply frequency out of limits ) Have the power company check the frequency and voltage of incoming power. If correct,for error code E5C,replace the speed control board. If correct, for error codes EA1, EA2, EA3, EA5, EAE, replace the main board.
EA2       (Power supply voltage too high ) Have the power company check the frequency and voltage of incoming power. If correct,for error code E5C,replace the speed control board. If correct, for error codes EA1, EA2, EA3, EA5, EAE, replace the main board.
EA3       (Power supply voltage to low ) Have the power company check the frequency and voltage of incoming power. If correct,for error code E5C,replace the speed control board. If correct, for error codes EA1, EA2, EA3, EA5, EAE, replace the main board.
EA5       ( Main voltage sensing failure ) Have the power company check the frequency and voltage of incoming power. If correct,for error code E5C,replace the speed control board. If correct, for error codes EA1, EA2, EA3, EA5, EAE, replace the main board.
EAE       ( Line safe relay sensing failure ) Have the power company check the frequency and voltage of incoming power. If correct,for error code E5C,replace the speed control board. If correct, for error codes EA1, EA2, EA3, EA5, EAE, replace the main board.
EB1       ( Incoming power frequency out of limits. )
EB2       ( Incoming line voltage above 130 vac. Check voltage If below 130 replace control )
EB3       ( Incoming line voltage below 90 VAC. Check voltage if above 90 replace control )
EF1       ( Clogged drain pump )
EF2       ( Too much soap. advise to reduce soap)
EBE       ( Console control problem .Replace control board )
EBF       ( Console control problem . Replace control board )
EF5       ( NTC temperature for the hot water valve over the limits.Hot and cold hoses switched)
EF6        ( Control reset ) unplug control, if not corrected ,replace control
EF8        ( Key Stuck ) Check for stuck buttons, replace user interface board.

F01      ( Internal control fault ) Unplug wait and restart. If no fix, replace main control
F02      ( Water fill temp problem) Hoses could be reversed, Check sensor (if below 3K or above 163K replace the sensor)
F03      ( Water fill / water level or drain pump problem ) Could be inlet water is turned off. Check pressure switch, valve, check drain pump.
F04      ( Washer not advancing or speed control problem)
F05      ( Stuck keypad or faulty connection at main control board) Check connections at boards
DO / DR  ( Door open or door issue,check reed switch)
DDO       ( Dispenser door open or dispenser door problem) Check reed switch and close door
San          ( Deep Clean   Sanitary cycle )
ERR          ( Error has been detected)
LOC         ( Control lock is activated )


Affinity Dryer codes:
E10    : General EEPROM fault , problem with communication between EEPROM and the micorprocessor. Clear code,exit mode,and start dryer , if problem persists replace control.
E11    : Checksum Error, Problem with communications or memory did not check. Clear code,exit mode,and start dryer , if problem persists replace control.
E12    : Non fatal R/W error, problem reading or writing to memory or input/output. Clear code,exit mode,and start dryer , if problem persists replace control.
E24    :  Control NTC Short circuit, Control thermistor or its wiring is shorted. Remove wires from thermistor. if reading is not 50k replace thermistor. If reading is within 50 k ,check wiring between thermistor and control. If good replace control.
E25    : Control NTC open circuit, control thermister or its wiring is open. Remove wires from thermistor. if reading is not 50k replace thermistor. If reading is within 50 k ,check wiring between thermistor and control. If good replace control.
E4A     : Program time out fault , the dryer time has exceeded program time for that cycle.
Press PAUSE, CANCEL, AND SELECT buttons for 6 seconds to exit test modes. Position cycle selector to Normal, temperature selector to HIGH HEAT and touch start. Check for anything that would extend dry times such as: no heat, restricted vent, blower fan blade broken or loose, dryer installed in closet with solid door, or bad connection in moisture sensor bar circuit or dirty bars. If dryer operates normal, replace control board.
E5B      : Heater Fault (no heating) Temperature reading of control thermistor has not changed in a certain amount of time. Position cycle selector to NORMAL, temperature selector to HIGH HEAT and touch start. Measure voltage across terminals on relay RL2 (heater relay) on control. If meter reads 240v on electric models and 120 volts on gas,replace control board. If meter reads zero, remove power from dryer. Disconnect wire going to NO terminal on the relay RL2. Reconnect power and measure voltage drop between terminal COM on relay RL2 and neutral. If meter reads zero,wire between incoming line and relay RL2 is open. If meter reads 120volts,check the rest of the heater circuit.
E68        : Key button stuck fault , one of the keys is stuck closed. Enter function test mode and perform key button test to determine which button is at fault. Carefully free the key and perform the test again. If button is free but the key stuck code still exists, replace control board.
E8C      : Too many trips in a period of time. The safety thermostat has tripped too many times within a certain time. Check for blocked lint filter,blocked exhaust,air leaks around air duct,broken blower blades,worn or loose drum seals, dryer installed in closet with solid doors or door seal not correctly seated.
EAF      : Watch dog reset, Microcontroller has been reset by internal Watchdog timer. Clear code,exit mode,and start dryer , if problem persists replace control.

More frigidaire Front load washers

1 Beep / E 10   Error: Water doesn't enter Cause: Water supply problem, Check kinks and faucets.
1 Beep / E 10   Error: Water leaks Cause: Water connections loose,household drain clog,oversudsing. Correct problems.
1 Beep / E 10   Error: Dispenser drawer is open Cause: Washer will not operate if drawer is open.
2 Beeps / E 20  Error: Water dosen't drain. Cause: Drain is kinked or household clog. Correct.
3 Beeps / E 30  Error: Drum overfilled. Cause: Inlet valve,pressure switch or control board failure.Select drain/spin to remove water. Restart.
4 Beeps / E 40  Error: Door is open. Cause: Washer will not operate if door is open. Close door.
5 Beeps / E 50  Error: Motor is overheated. Cause: Wait 30 minutes to cool down. Restart.
7 Beeps / E 70  Error: Cold water doesn't enter. Cause: Hoses crossed,faucet problem.
15 Beeps / E F0 Error: Oversudsing. Cause: Too much detergent,or improper detergent for machine.
15 Beeps / E F0 Error: Hot water doesn't enter. Cause: Hoses crossed,faucet problem.

Frigidaire Refrigerator fault error codes for dual control:

Start up Test
At the time the product is connected to line voltage it will run a self test. If all components pass, your
set points will appear in the display. If there is a failure you will see a fault code appear in the display.
Test 1 - CODE ef     : replace Evaporator fan motor. Alternating E in food display, F in freezer display indicates test failed.
Test 2 - Freezer Thermistor. Flash 2 or 3 if failed test
Test 3 - Food Thermistor. Flash 2 or 3 if failed test. Flash “2” Thermistor is open. Flash “3” Thermistor
is sensor shorted.
Test 4 - Damper. Flash "4" in food display indicates the damper test failed.