Search
By part number only
Browse by Manufacturer
Click for the BBB Business Review of this Appliances - Major - Parts & Supplies in Lakeland FL
Press ( CTRL )  and the letter ( F ) on your keyboard to pop up a search box. The you may put in your code to make your search easier.


Range, Refrigeration and washer Fault Codes are very much used these days on the newer Electonic Controls.

This guide may be incomplete as manufactures use different parts on different models. This is a general guide to fault codes. We assume no responsibility for any action taken on your part as a result of using this guide. Consult your owners manual, as it may give the fault codes for your particular model. Contact a local servicer for repairs.

If you didn't find your model/ brand in these fault code charts Contact us! Maybe we can help find your code.




Asko Dishwasher error codes

Failure Code Condition Check/Repair

F1 Water heating fault, selected temperature not reached within 60 minutes ·  1. Incoming water temperature too cool
2. Heating element burned out
3. Thermostat defective
 
F2 High water level
1.  Plugged/Bad water pump
2.  Defective water inlet valve

F3 Thermistor fault
1.  Open thermistor
2.  Bad wiring to thermistor

F4 Fault with water fill (only on machines with level-controlled fill)

Note: Lights blinking, pump running and controls dead indicates an over fill fault

1. Disconnect the power to the unit

2. Remove the lower access panels and check the tray under the dishwasher (you will probably find it is full of water)

3. Use a towel or a sponge to remove the water

4. There is a float that should stop the operation of the dishwasher and run the pump if water is in this tray. Check this pump to see if it is functional

5. Test the dishwasher


6. If there are no leaks from the dishwasher into the pan, check the drain hose under the sink

7. The drain hose must run up to the top of the underside of the countertop then down to the drain. (If the hose is not set up like this, water from the sink drain will flow into the dishwasher and overfill the tray

*Faults may vary by model. Use this as a general guide.


Asko Dryer error codes

Failure Code Condition Check/Repair
 
F1 Condensate drain overfilling.
1.  Check condensate reservoir pump and drain tube.
 
F2 Maximum drying time exceeded (3hrs)
1.  Check for tripped circuit breaker or blown fuse
2.  Check ductwork for lint build-up
3.  Check hi-limit and cycling thermostat
4.  Check heating element

F3 Thermistor fault
1.  Open thermistor, replace
2.  Bad wiring to thermistor

F4 Too much lint in the lint filter, front housing, or in the condenser.
1.  Clean lint from lint filter and/or condenser

F5 Fault in the moisture sensor · Lint covering sensor in front of housing
1.  Bad sensor
2.  Bad wiring to sensor


Asko washer error codes


Failure Code Condition Check/Repair
 
F1 Water supply/low water fill.
1.  Check water supply to machine.
2.  Replace water inlet valve.
 
F2 Water level too high.
1.  Plugged/Bad water pump.
2.  Faulty water valve.
 
F3 Pump problem.
1.  Check pump trap and clean.
 
F4 Thermistor problem.
1.  Open thermistor, replace.
2.  Bad wiring to thermistor.
 
F5 Fault in thermal cutout or heating pause fault.
1.  Selected temperature not reached in 90 minutes.
2.  Check heating element.
3.  Check thermostat.
 
F6 Motor fault.
1.  Check wiring to motor.
2.  Replace motor if necessary.
 
F7 Door lock release fault.
1.  Bent pull-rod for door latch.
2.  Bad door latch solenoid.
 
00 00 Machine did not spin.
 1.  Check load for out of balance.
2.   Redistribute load and restart.


 


_________